911 Carrera 3.0
Registry

Serving North American & Canadian owners of
1976-1977 Porsche 911 Carrera 3.0 cars


Go Back   911 Carrera 3.0 US Registry Forums > Articles > Maintenance & Repair

Maintenance & Repair Share common repair and maintenance routines here.

Reply
 
Article Tools Display Modes
  Post #1 (URL for Single or Threaded post)  
Old 08-25-2013, 11:50 PM
Mills911C3's Avatar
Mills911C3 Mills911C3 is offline
911 Carerra 3.0 Advocate
 
Join Date: May 2013
Posts: 87
Arrow Repair 915 Transmission 'Stub Shaft Seals'.

I will be posting pictures & narration of the repair of my stub shaft oil seals for our 'Home Repair' patrons.
My starting point:
1:Jack up & safely support car at least 24" to gain access to freely turn
wrenches.
2:Secure wheels to prevent rotation while removing CV Joint 6mm hex
socket screws to Stub Shaft Flange. I chose to never completely
remove these screws keeping the CV Joint in place to the axle.
3:I chose to support CV Joints from hanging freely by a stand.
4:Clean out Stub Shaft Flange grerase. Clean out CV Boot grease.
5:I inserted 2 screws, as shown, to brace from rotation when removing 19
mm Retaining Hex Bolt.
6:Pry out ols seals. Shown suggestion of pry bar.
7:Replace new seals, Dry, by slowly tapping in to place then pound them
in,recessed ~1/16", by using a Rubber Mallet.
8:Replace Stub Shaft, by slowly engaguing splines in to Trans Gears to
its original position. Not to worry in replacing Stub Shaft Flange at same degree
removed from. Replace 2 screws as bracing & position pry bar to
prevent rotation & tighten stub Shaft Bolt to 23 Ft#.
9:Repack stub shaft center with grease. Repack CV Boots.
10:Lift the Wheel Hub, compressing the shock as far as can not actually
lifting the car from the Jack Supports. This is to gain free space to position
the CV Joint Boot Flange to the stub shaft flange face.
11:Secure the hex socket screws to -- Ft/#.
12: Replacing & Securing Boot Clamps. *Very Important*, if you don't
have or can't rent or don't have access to, **or don't happen to be fortunate
enough as I, to have had a Father who was a Veterinarian who handed down
shown "Bulls Testicle Removal Tool", then you will have to buy a Clamp Crimping Tool.
Attached Thumbnails
Loosening Joint Flange Attachment 6mm Hex Socket Bolts.jpg   CV Joint Proping 'Close-Up'.jpg   Joint Flange 19mm Hex Bolt after CV Joint Grease is removed.jpg   screws position as rotation stop.jpg   Stub Shaft and Retaining Screw - removed.jpg   pry bars - smaller did not work - too much work.jpg   prying old seal out - 2 - RS.jpg   starting seal insertion -2.jpg   packed stub shaft cavity.jpg   CV Joint Boot Clamp - Special Clamp Crimping Device.jpg  


Last edited by Mills911C3; 02-13-2014 at 10:13 PM. Reason: correct sentence word
Scroll Up!
Reply

Article Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 05:58 AM.


Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2019, vBulletin Solutions, Inc.
Copyright 2010-2013, Porsche Club of America. This site is owned and operated by the
Porsche Club of America. It is not affiliated in any way with Porsche AG or Porsche Cars North America.